What Oil Filter Use On 20 Hp Kohler Engine

Kohler Engine Oil and Filters

Kohler Pro 300-hour, extended life synthetic oil and filter provides unmatched protection for Walker Mowers equipped with Kohler engines. This 10W-50 fully-synthetic oil has a 3x longer life extending oil changes while providing platonic engine protection in all-seasons and all-temperatures.

• 3X longer oil change interval
• Engineered past Amsoil exclusively for Kohler
• Fully synthetic oil formulated specifically for extended oil modify intervals in Kohler air-cooled engines
• Guaranteed 300-hour oil change interval on most KOHLER ^® gas engines by, present, and futurity
• 10W-50 viscosity for all flavor functioning
• Extra corrosion inhibitor for seasonal storage and multi-season use
• Lower oil consumption than conventional oil
• Warranty approved for KOHLER engines

One Oil For ALL Seasons

• Full constructed base of operations oil for superior lubrication with pre-determined backdrop
• More durable fluid film than conventional oils for improved wear protection
• Protects against deposit formation and viscosity increase
• 10W-l Viscosity Formulated for All-Season Performance
• Full Operating Range From -20°F to 110°F

Why KOHLER PRO Oil Filter?

• Extended Life Oil Filter Required for 300-Hr Oil Change Interval
• Premium Media Selected to Provide Extra Chapters With Superior Filtration
• Robust Structure for Longer Life
• ten-Micron Fiberglass Media Supported past Wire Backing
• Metal End Caps
• High Durability Anti-Drain Back Valve & Sealing Gasket
• Fabricated in Usa

Extended Life Filter (left), Standard Filter (right)

Save With Reduced Oil Changes

Service Data and Resources

Oil and Filter Ordering Info

Kohler SAE 10W-l Oil
1 U.S. Quart (946 mL)
Kohler P/N 25 357 72-S

Kohler PRO
Oil Filter
Kohler P/Northward 25 050 53-S

Kohler SAE 10W-50 Oil
5 U.Due south. Quart (iv,730 mL)
Kohler P/N 25 357 75-S

Kohler PRO Oil Alter Kit
2 Quarts Oil + Oil Filter
Kohler P/Due north 25 850 02-S

Engine Burglary Oil

The engine is serviced with Kohler PRO 10W-fifty synthetic oil and a Kohler PRO filter from the factory. Both are rated for 300 hours. A break-in oil change is not required. The engine crankcase oil and the filter must be changed after every 300 hours of functioning.

Checking Engine Crankcase Oil Level

Bank check the engine crankcase oil level earlier utilize and after each eight hours of continuous operation.

IMPORTANT: The importance of checking and maintaining the proper crankcase oil level cannot be overemphasized. Check the oil level Earlier EACH Utilise.

1. Park the mower on a level surface with the engine stopped. Also, make certain the engine is cool and oil has had time to drain into the sump [allow at least five (5) minutes subsequently stopping the engine].
   IMPORTANT: NEVER check or add oil with the engine running.
2. Before removing the dipstick, clean the area around the dipstick to keep any dirt or debris out of the engine.
3. Remove the dipstick, wipe off with a clean rag, then reinsert the dipstick into the tube and press all the way down.
4. Remove the dipstick again and bank check the oil level on the dipstick. The oil level should exist inside the "Operating Range" on the dipstick (between the "50" mark and the "F" mark).
   Of import: Exercise NOT operate engine without a sufficient oil supply in the crankcase. DO Non operate with the oil level below the "Fifty" mark or higher up the "F" marking on the dipstick.
5. If boosted oil is needed, refer to the Specifications section of your operator'due south manual for proper crankcase lubricant. Fill upward to, but non above, the "F" marking on the dipstick.
   IMPORTANT: DO NOT overfill the crankcase (oil above "F" mark) every bit this Tin result in engine overheating, loss of power, and possible engine damage.

Changing Engine Crankcase Oil and Filter

When using Kohler PRO 300 Hour Extended Life Synthetic Engine oil, change the engine crankcase oil and oil filter subsequently every 300 hours.

Note: Kohler PRO oil and filter are non required, merely recommended. If conventional oil and filters are used in the tractor, the oil must be changed afterward every 100 hours of performance, and the filter must exist changed after every 200 hours. See the Specification department of your operator's manual for details on which oil and filters are supported.

1. Park the mower on a level surface with the engine stopped. The engine oil should be warm before draining. If non warm from performance, start the engine and run a few minutes to warm the oil.
2. Before removing the dipstick, clean the surface area around it to continue whatsoever dirt or droppings out of the engine.
3. Remove the dipstick and open oil bleed valve and drain the oil into a suitable container. Be sure to permit aplenty time for complete drainage.
4. Before removing the oil filter, clean the area effectually the filter to keep clay and debris out of the engine.
5. Remove the old oil filter and wipe off the filter mounting surface on the engine.
6. Utilize a thin coating of clean oil to the rubber gasket on the replacement oil filter.
   IMPORTANT: Employ But oil filters from the engine manufacturer (Kohler 25-050-53-S). Aftermarket oil filters may non seal properly and/or may non have the right force per unit area relief valve for proper lubrication.
7. Install the new oil filter on the engine. Turn the filter clockwise until the condom gasket contacts the sealing surface, then tighten an additional iii/4 to i turn.
8. Close the oil drain valve and tighten until snug. Do non over-tighten.
9. Fill the crankcase with new, clean oil. Kohler PRO 300 Hr Synthetic Engine Oil (SAE 10W-50) and filters are highly recommended. Refer to Crankcase Lubricant in the Specifications department of your operator'due south transmission for other options. Fill up up to, but non to a higher place, the "F" mark on the dipstick. Crankcase capacity is two.0 quarts (1.ix liters) plus 1/2 pint (0.24 liters) for the new oil filter.
   Important: Check the dipstick reading before calculation the last ane/2 pint of oil and fill only to the "F" mark. Practise NOT overfill the crankcase (oil above "F" mark) as this CAN result in engine overheating, loss of power, and possible engine damage.
10. Outset the engine and bank check for oil leaks around the oil filter. End the engine, recheck the oil level, and add oil if necessary. (When the engine is first operated with a new oil filter, the oil level volition drop slightly as the filter is filled with oil.)

What Oil Filter Use On 20 Hp Kohler Engine,

Source: https://www.walker.com/kohler-engine-oil

Posted by: bellofflon.blogspot.com

Share this post